Cisco 자격증 640-802 시험문제와 답

우리ITExamDump 에서 제공하는 학습가이드에는 IT전문가들이 만들어낸 시험대비 자료들과Cisco 640-802인증시험의 완벽한 문제와 답들입니다. 그리고 우리ITExamDump에서는 IT업계에서의 높은 신뢰감으로 여러분들한테 100%보장을 드립니다. 우리에 믿음을 드리기 위하여Cisco 640-802관련자료의 일부분 문제와 답 등 샘플을 무료로 다운받아 체험해볼수 있게 제공합니다.

만약 시험만 응시하고 싶으시다면 우리의 최신Cisco 640-802자료로 시험 패스하실 수 있습니다. ITExamDump 의 학습가이드에는Cisco 640-802인증시험의 예상문제, 시험문제와 답 임으로 100% 시험을 패스할 수 있습니다.우리의Cisco 640-802시험자료로 충분한 시험준비하시는것이 좋을것 같습니다. 그리고 우리는 일년무료 업데이트를 제공합니다.

Cisco 640-802인증은 아주 중요한 인증시험중의 하나입니다. ITExamDump의 베터랑의 전문가들이 오랜 풍부한 경험과 IT지식으로 만들어낸 IT관연인증시험 자격증자료들입니다. 이런 자료들은 여러분이Cisco인증시험중의640-802시험을 안전하게 패스하도록 도와줍니다. ITExamDump에서 제공하는 덤프들은 모두 100%통과 율을 보장하며 그리고 일년무료 업뎃을 제공합니다

시험 번호/코드: 640-802

시험 이름: Cisco (Cisco Certified Network Associate(CCNA))

Cisco인증 640-802시험은 멋진 IT전문가로 거듭나는 길에서 반드시 넘어야할 높은 산입니다. Cisco인증 640-802시험문제패스가 어렵다한들ITExamDump덤프만 있으면 패스도 간단한 일로 변경됩니다. ITExamDump의Cisco인증 640-802덤프는 100%시험패스율을 보장합니다. Cisco인증 640-802시험문제가 업데이트되면Cisco인증 640-802덤프도 바로 업데이트하여 무료 업데이트서비스를 제공해드리기에 덤프유효기간을 연장해는것으로 됩니다.

우리ITExamDump에는 아주 엘리트한 전문가들로 구성된 팀입니다. 우리는 아주 정확하게 또한 아주 신속히Cisco 640-802관한 자료를 제공하며, 업데이트될경우 또한 아주 빠르게 뉴버전을 여러분한테 보내드립니다. ITExamDump는 관련업계에서도 우리만의 브랜드이미지를 지니고 있으며 많은 고객들의 찬사를 받았습니다. 현재Cisco 640-802인증시험패스는 아주 어렵습니다, 하지만 ITExamDump의 자료로 충분히 시험 패스할 수 있습니다.

ITExamDump 에서는 최선을 다해 여러분이Cisco 640-802인증시험을 패스하도록 도울 것이며 여러분은 ITExamDump에서Cisco 640-802덤프의 일부분의 문제와 답을 무료로 다운받으실 수 잇습니다. ITExamDump 선택함으로Cisco 640-802인증시험통과는 물론ITExamDump 제공하는 일년무료 업데이트서비스를 제공받을 수 있으며 ITExamDump의 인증덤프로 시험에서 떨어졌다면 100% 덤프비용 전액환불을 약속 드립니다.

아직도 Cisco인증640-802시험준비를 어떻게 해야 할지 망설이고 계시나요? 고객님의 IT인증시험준비길에는 언제나 ITExamDump가 곁을 지켜주고 있습니다. ITExamDump시험공부자료를 선택하시면 자격증취득의 소원이 이루어집니다. Cisco인증640-802시험덤프는ITExamDump가 최고의 선택입니다.

640-802 덤프무료샘플다운로드하기: http://www.itexamdump.com/640-802.html

NO.1 Which command reveals the last method used to powercycle a router?
A. show reload
B. show boot
C. show running-config
D. show version
Answer: D

Cisco   640-802기출문제   640-802 dump

NO.2 Which three options are valid WAN connectivity methods? (Choose three.)
A. PPP
B. WAP
C. HDLC
D. MPLS
E. L2TPv3
F. ATM
Answer: ACF

Cisco   640-802최신덤프   640-802최신덤프   640-802 dumps   640-802

NO.3 What must be set correctly when configuring a serial interface so that higher-level protocols calculate
the
best route?
A. bandwidth
B. delay
C. load
D. reliability
Answer: A

Cisco dump   640-802 pdf   640-802인증

NO.4 Which command is used to see the path taken by packets across an IP network?
A. show ip route
B. show route
C. traceroute
D. trace ip route
Answer: C

Cisco   640-802최신덤프   640-802

NO.5 Which two addresses can be assigned to a host with a subnet mask of 255.255.254.0? (Choose two.)
A. 113.10.4.0
B. 186.54.3.0
C. 175.33.3.255
D. 26.35.2.255
E. 17.35.36.0
Answer: BD

Cisco자료   640-802자격증   640-802시험문제   640-802자격증

NO.6 Which command would you configure globally on a Cisco router that would allow you to view directly
connected Cisco devices?
A. enable cdp
B. cdp enable
C. cdp run
D. run cdp
Answer: C

Cisco   640-802   640-802 dump   640-802시험문제   640-802   640-802자료

NO.7 Which command is used to debug a ping command?
A. debug icmp
B. debug ip icmp
C. debug tcp
D. debug packet
Answer: B

Cisco최신덤프   640-802   640-802자료   640-802

NO.8 Your ISP has given you the address 223.5.14.6/29 to assign to your router's interface. They have also
given you the default gateway address of 223.5.14.7. After you have configured the address, the router is
unable to ping any remote devices. What is preventing the router from pinging remote devices?
A. The default gateway is not an address on this subnet.
B. The default gateway is the broadcast address for this subnet.
C. The IP address is the broadcast address for this subnet.
D. The IP address is an invalid class D multicast address.
Answer: B

Cisco   640-802   640-802 dump   640-802   640-802자격증

NO.9 The network default gateway applying to a host by DHCP is 192.168.5.33/28. Which option is the valid
IP address of this host?
A. 192.168.5.55
B. 192.168.5.47
C. 192.168.5.40
D. 192.168.5.32
E. 192.168.5.14
Answer: C

Cisco기출문제   640-802시험문제   640-802 dumps   640-802

NO.10 When configuring a serial interface on a router, what is the default encapsulation?
A. atm-dxi
B. frame-relay
C. hdlc
D. lapb
E. ppp
Answer: C

Cisco자료   640-802기출문제   640-802자격증   640-802   640-802자격증

NO.11 Data transfer is slow between the source and destination. The quality of service requested by the
transport layer in the OSI reference model is not being maintained. To fix this issue, at which layer should
the troubleshooting process begin?
A. presentation
B. session
C. transport
D. network
E. physical
Answer: D

Cisco   640-802덤프   640-802자격증   640-802 dump   640-802 pdf

NO.12 Workstation A has been assigned an IP address of 192.0.2.24/28. Workstation B has been assigned an
IP address of 192.0.2.100/28. The two workstations are connected with a straight-through cable. Attempts
to ping between the hosts are unsuccessful. What two things can be done to allow communications
between the hosts? (Choose two.)
A. Replace the straight-through cable with a crossover cable.
B. Change the subnet mask of the hosts to /25.
C. Change the subnet mask of the hosts to /26.
D. Change the address of Workstation A to 192.0.2.15.
E. Change the address of Workstation B to 192.0.2.111.
Answer: AB

Cisco pdf   640-802덤프   640-802   640-802

NO.13 Cisco Catalyst switches CAT1 and CAT2 have a connection between them using ports FA0/13. An 802.
1Q trunk is configured between the two switches. On CAT1, VLAN 10 is chosen as native, but on CAT2
the native VLAN is not specified.What will happen in this scenario?
A. 802.1Q giants frames could saturate the link.
B. VLAN 10 on CAT1 and VLAN 1 on CAT2 will send untagged frames.
C. A native VLAN mismatch error message will appear.
D. VLAN 10 on CAT1 and VLAN 1 on CAT2 will send tagged frames.
Answer: C

Cisco   640-802   640-802자격증   640-802최신덤프

NO.14 A system administrator types the command to change the hostname of a router. Where on the Cisco
IFS is that change stored?
A. NVRAM
B. RAM
C. FLASH
D. ROM
E. PCMCIA
Answer: B

Cisco   640-802 dumps   640-802   640-802자격증   640-802인증

NO.15 If IP routing is enabled, which two commands set the gateway of last resort to the default gateway?
(Choose two.)
A. ip default-gateway 0.0.0.0
B. ip route 172.16.2.1 0.0.0.0 0.0.0.0
C. ip default-network 0.0.0.0
D. ip default-route 0.0.0.0 0.0.0.0 172.16.2.1
E. ip route 0.0.0.0 0.0.0.0 172.16.2.1
Answer: CE

Cisco   640-802   640-802 dumps

NO.16 A company implements video conferencing over IP on their Ethernet LAN. The users notice that the
network slows down, and the video either stutters or fails completely. What is the most likely reason for
this?
A. minimum cell rate (MCR)
B. quality of service (QoS)
C. modulation
D. packet switching exchange (PSE)
E. reliable transport protocol (RTP)
Answer: B

Cisco   640-802   640-802 dumps   640-802

NO.17 Which command shows system hardware and software version information?
A. show configuration
B. show environment
C. show inventory
D. show platform
E. show version
Answer: E

Cisco   640-802   640-802

NO.18 Which command is used to copy the configuration from RAM into NVRAM?
A. copy running-config startup-config
B. copy startup-config: running-config:
C. copy running config startup config
D. copy startup config running config
E. write terminal
Answer: A

Cisco   640-802   640-802   640-802   640-802기출문제

NO.19 Which protocols are found in the network layer of the OSI reference model and are responsible for
path determination and traffic switching?
A. LAN
B. routing
C. WAN
D. network
Answer: B

Cisco기출문제   640-802   640-802최신덤프   640-802 pdf

NO.20 A network administrator must configure 200 switch ports to accept traffic from only the currently
attached host devices. What would be the most efficient way to configure MAC-level security on all these
ports?
A. Visually verify the MAC addresses and then telnet to the switches to enter the switchport-port security
mac-address command.
B. Have end users e-mail their MAC addresses. Telnet to the switch to enter the switchport-port security
mac-address command.
C. Use the switchport port-security MAC address sticky command on all the switch ports that have end
devices connected to them.
D. Use show mac-address-table to determine the addresses that are associated with each port and then
enter the commands on each switch for MAC address port-security.
Answer: C

Cisco   640-802자격증   640-802자격증   640-802기출문제

NO.21 The network administrator has asked you to check the status of the workstation's IP stack by pinging the
loopback address. Which address would you ping to perform this task?
A. 10.1.1.1
B. 127.0.0.1
C. 192.168.0.1
D. 239.1.1.1
Answer: B

Cisco기출문제   640-802   640-802기출문제   640-802

NO.22 Which command would correctly configure a serial port on a router with the last usable host address in
the 192.216.32.32/29 subnet?
A. Router(config-if)# ip address 192.216.32.38 255.255.255.240
B. Router(config-if)# ip address 192.216.32.39 255.255.255.224
C. Router(config-if)# ip address 192.216.32.63 255.255.255.248
D. Router(config-if)# ip address 192.216.32.39 255.255.255.248
E. Router(config-if)# ip address 192.216.32.63 255.255.255.248
F. Router(config-if)# ip address 192.216.32.38 255.255.255.248
Answer: F

Cisco덤프   640-802 dump   640-802자격증   640-802   640-802

NO.23 What is the difference between a CSU/DSU and a modem?
A. A CSU/DSU converts analog signals from a router to a leased line; a modem converts analog signals
from a router to a leased line.
B. A CSU/DSU converts analog signals from a router to a phone line; a modem converts digital signals
from a router to a leased line.
C. A CSU/DSU converts digital signals from a router to a phone line; a modem converts analog signals
from a router to a phone line.
D. A CSU/DSU converts digital signals from a router to a leased line; a modem converts digital signals
from a router to a phone line.
Answer: D

Cisco   640-802기출문제   640-802 dumps   640-802최신덤프

NO.24 When you are logged into a switch, which prompt indicates that you are in privileged mode?
A. %
B. @
C. >
D. $
E. #
Answer: E

Cisco   640-802   640-802최신덤프

NO.25 Which command is used to load a configuration from a TFTP server and merge the configuration into
RAM?
A. copy running-config: TFTP:
B. copy TFTP: running-config
C. copy TFTP: startup-config
D. copy startup-config: TFTP:
Answer: B

Cisco   640-802   640-802   640-802기출문제   640-802   640-802

NO.26 Which command displays CPU utilization?
A. show protocols
B. show process
C. show system
D. show version
Answer: B

Cisco   640-802 dumps   640-802   640-802 dump   640-802

NO.27 Which layer in the OSI reference model is responsible for determining the availability of the receiving
program and checking to see if enough resources exist for that communication?
A. transport
B. network
C. presentation
D. session
E. application
Answer: E

Cisco기출문제   640-802   640-802최신덤프   640-802   640-802   640-802 dumps

NO.28 Refer to the exhibit.
Which WAN protocol is being used?
A. ATM
B. HDLC
C. Frame Relay
D. PPP
Answer: C

Cisco인증   640-802자료   640-802자격증   640-802

NO.29 When troubleshooting a Frame Relay connection, what is the first step when performing a loopback
test?
A. Set the encapsulation of the interface to HDLC.
B. Place the CSU/DSU in local-loop mode.
C. Enable local-loop mode on the DCE Frame Relay router.
D. Verify that the encapsulation is set to Frame Relay.
Answer: A

Cisco   640-802시험문제   640-802 dumps   640-802 dumps   640-802인증

NO.30 Which command is used to configure a default route?
A. ip route 172.16.1.0 255.255.255.0 0.0.0.0
B. ip route 172.16.1.0 255.255.255.0 172.16.2.1
C. ip route 0.0.0.0 255.255.255.0 172.16.2.1
D. ip route 0.0.0.0 0.0.0.0 172.16.2.1
Answer: D

Cisco자격증   640-802   640-802 pdf   640-802자격증

ITExamDump의Cisco인증 640-802덤프는 몇십년간 IT업계에 종사한 전문가들이Cisco인증 640-802 실제 시험에 대비하여 제작한 시험준비 공부가이드입니다. Cisco인증 640-802덤프공부가이드로 시험준비공부를 하시면 시험패스가 쉬워집니다. 공부하는 시간도 적어지고 다른 공부자료에 투자하는 돈도 줄어듭니다. ITExamDump의Cisco인증 640-802덤프는 Cisco인증 640-802시험패스의 특효약입니다.